This chapter describes how to install a new diskimage on a NetWinder by removing the hard disk and installing it as the slave drive in another system. This method is not recommended since it will void the warrantee, but its a practical method especially for those people with very small hard disks.
This method requires a second computer where the NetWinder's hard disk can be installed. The second machine could be another NetWinder, or an ordinary PC running some form of unix. In the case of a regular PC, an adaptor cable is required since the NetWinder hard drive is of the 2.5" laptop variety, which will not plug directly into the normal IDE connectors. Adaptors are available at most computer stores for about $10.
Static electricity can kill a NetWinder! Be sure to be properly grounded before you start poking around inside your computer.
The NetWinder's hard drive should be connected to the host computers IDE controller, and (possibly) the master/slave jumper will need to be adjusted on the NetWinder's drive. To gain access to the drive, open the four screws on the bottom of the NetWinder. Usually it's possible to move the NetWinder close enough to the PC so that the cable can be directly connected, if not, you'll have to remove the hard drive itself (the screws are on the bottom of the motherboard).
Once the drive is connected, the PC can be powered up. Do whatever is
necessary for the drive to be detected (this might mean going into the BIOS
and specifying the drive parameters, or on modern PC's, the drive will be
auto-detected). I'll assume for the purpose of this example that the PC's
main hard drive is
/dev/hda and that the NetWinder's drive is
/dev/hdb - but you'll have to verify that this is the case on your
machine (use the
dmesg command for this).
There must be enough room to install the new disk image on the NetWinder's drive. You have the option of moving/deleting files to free up a partition, or you might choose to format the NetWinder's hard disk completely and repartition it as you wish. I cannot give you a step-by-step guide here, so I'll describe the available options and let you decide.
To transfer files between partitions, you need to mount both partitions and
then use the
rm commands. Two mountpoints are
required for this - you can use any two directories - for example
/mnt/two. Of course the directories must
exist before they can be used, so go wild with the
Then mount the two partitions (picking on
/dev/hdb2 for this example):
mount /dev/hdb1 /mnt/one mount /dev/hdb2 /mnt/two
Now files can be copied from
vice-versa) using the
cp command. To remove the originals after
they've been copied, use the
rm command. When you're done, unmount
the partitions again:
sync umount /mnt/one umount /mnt/two
Once a partition has been cleared of files, or if you don't want to keep the old files, the format command can be used to initialize a new filesystem. This will completely wipe out everything on the partition, with no way to restore it. Use with care, and check very carefully that the correct partition and drive are specified.
The preceeding example will format the first partition on the second (slave)
drive, presumably the NetWinder drive. In case you're not clear on the
naming convention yet, the drives are called
/dev/hdXY where X is a
a for the first drive,
b for the second, etc) and
Y is a number indicating the partition (starting from one).
In some cases it may be desirable to repartition the entire drive, for example if you are updating an old system and don't want to keep the old version anyhow. Note that after repartitioning, you must format the partitions, and this will destroy all data on the drive.
To adjust the partition tables, use the
fdisk command. You have
to tell it which drive you want to repartition - for example say
/dev/hdb to adjust the partition table on the second (slave) drive.
The rest of the commands (for deleting a partition, creating a new one, etc)
are explained in the on-line help. There is also a nice man page (
fdisk) that gives more information.
The recommended disk layout is as follows: the first partition is the root
filesystem (type 83, Linux) usually about 1 GB in size. The second
partition is used for swap (type 82, Linux swap) and is 64 to 128 MB in
size. Anything remaining space is allocated to third partition and gets
To install the image, you need to ensure that both the source and
destination partitions are mounted, then you can use the
command to extract files from the diskimage. Most likely, the diskimage is
located on your main disk (hda) and the destination is the first partition
on hdb. In this case, the appropriate commands are as follows:
mount /dev/hdb1 /mnt/hdb1 cd /mnt/hdb1 tar zxpf /path/to/YourImage.tar.gz
You'll need to ensure that the mountpoint
/dev/hdb1 exists (or use
a different name), and you'll need to specify an appropriate path and
filname instead of
path/to/YourImage. This process should be
pretty quick, about 5-10 minutes, since the data is moving over the IDE bus
After the installation of the disk image is completed, be sure to review the
etc/fstab file in the installed image. The entries in this file
must correspond with the way the partitions are used, eg. if the first
partition contains the main image, then it should be mounted as
in the fstab file. Keep in mind that the drive names listed in the fstab
file should be those that will be seen when the disk drive is booted on the
/dev/hda in most cases). Also be sure to edit the right
etc/fstab file - you want to edit the one in the image you just
untarred, not the one belonging to the host PC.
The drive can then be unmounted and the PC can be powered down. The
NetWinder's hard disk should then be reinstalled. If the partition usage
has changed, then firmware settings may need to be changed. Consult section
2.5 for details, but remember to use the appropriate
value for your particular situation.